Rimozione VirtualBox + Problema Wifi

filename: /lib/modules/5.8.18-100.fc31.x86_64/kernel/drivers/net/wireless/8821ce.ko
version: v5.5.2_34066.20190614_COEX20180712-3232
author: Realtek Semiconductor Corp.
description: Realtek Wireless Lan Driver
license: GPL
srcversion: B43ACB057D7359CC4D85C68
alias: pci:v000010ECd0000C82Bsvsdbcsci*
alias: pci:v000010ECd0000C82Asvsdbcsci*
alias: pci:v000010ECd0000C821svsdbcsci*
depends: cfg80211
retpoline: Y
name: 8821ce
vermagic: 5.4.8-200.fc31.x86_64 SMP mod_unload
parm: rtw_wireless_mode:int
parm: rtw_ips_mode:The default IPS mode (int)
parm: rtw_lps_level:The default LPS level (int)
parm: rtw_lps_chk_by_tp:int
parm: rtw_max_bss_cnt:int
parm: rtw_usb_rxagg_mode:int
parm: rtw_dynamic_agg_enable:int
parm: rtw_tx_bw_mode:The max tx bw for 2.4G and 5G. format is the same as rtw_bw_mode (uint)
parm: rtw_rx_ampdu_sz_limit_1ss:RX AMPDU size limit for 1SS link of each BW, 0xFF: no limitation (array of uint)
parm: rtw_rx_ampdu_sz_limit_2ss:RX AMPDU size limit for 2SS link of each BW, 0xFF: no limitation (array of uint)
parm: rtw_rx_ampdu_sz_limit_3ss:RX AMPDU size limit for 3SS link of each BW, 0xFF: no limitation (array of uint)
parm: rtw_rx_ampdu_sz_limit_4ss:RX AMPDU size limit for 4SS link of each BW, 0xFF: no limitation (array of uint)
parm: rtw_vht_enable:int
parm: rtw_vht_rx_mcs_map:VHT RX MCS map (uint)
parm: rtw_rf_config:int
parm: rtw_country_code:The default country code (in alpha2) (charp)
parm: rtw_channel_plan:The default chplan ID when rtw_alpha2 is not specified or valid (int)
parm: rtw_excl_chs:exclusive channel array (array of uint)
parm: rtw_btcoex_enable:BT co-existence on/off, 0:off, 1:on, 2:by efuse (int)
parm: rtw_ant_num:Antenna number setting, 0:by efuse (int)
parm: rtw_qos_opt_enable:int
parm: ifname:The default name to allocate for first interface (charp)
parm: if2name:The default name to allocate for second interface (charp)
parm: rtw_pwrtrim_enable:int
parm: rtw_initmac:charp
parm: rtw_special_rf_path:int
parm: rtw_chip_version:int
parm: rtw_rfintfs:int
parm: rtw_lbkmode:int
parm: rtw_network_mode:int
parm: rtw_channel:int
parm: rtw_mp_mode:int
parm: rtw_wmm_enable:int
parm: rtw_uapsd_max_sp:int
parm: rtw_uapsd_ac_enable:int
parm: rtw_wmm_smart_ps:int
parm: rtw_vrtl_carrier_sense:int
parm: rtw_vcs_type:int
parm: rtw_busy_thresh:int
parm: rtw_ht_enable:int
parm: rtw_bw_mode:int
parm: rtw_ampdu_enable:int
parm: rtw_rx_stbc:int
parm: rtw_rx_ampdu_amsdu:int
parm: rtw_tx_ampdu_amsdu:int
parm: rtw_lowrate_two_xmit:int
parm: rtw_power_mgnt:int
parm: rtw_smart_ps:int
parm: rtw_low_power:int
parm: rtw_wifi_spec:int
parm: rtw_full_ch_in_p2p_handshake:int
parm: rtw_antdiv_cfg:int
parm: rtw_antdiv_type:int
parm: rtw_drv_ant_band_switch:int
parm: rtw_single_ant_path:int
parm: rtw_switch_usb_mode:int
parm: rtw_enusbss:int
parm: rtw_hwpdn_mode:int
parm: rtw_hwpwrp_detect:int
parm: rtw_hw_wps_pbc:int
parm: rtw_check_hw_status:int
parm: rtw_pci_aspm_enable:int
parm: rtw_max_roaming_times:The max roaming times to try (uint)
parm: rtw_mc2u_disable:int
parm: rtw_notch_filter:0:Disable, 1:Enable, 2:Enable only for P2P (uint)
parm: rtw_hiq_filter:0:allow all, 1:allow special, 2:deny all (uint)
parm: rtw_adaptivity_en:0:disable, 1:enable (uint)
parm: rtw_adaptivity_mode:0:normal, 1:carrier sense (uint)
parm: rtw_adaptivity_th_l2h_ini:th_l2h_ini for Adaptivity (int)
parm: rtw_adaptivity_th_edcca_hl_diff:th_edcca_hl_diff for Adaptivity (int)
parm: rtw_amplifier_type_2g:BIT3:2G ext-PA, BIT4:2G ext-LNA (uint)
parm: rtw_amplifier_type_5g:BIT6:5G ext-PA, BIT7:5G ext-LNA (uint)
parm: rtw_RFE_type:default init value:64 (uint)
parm: rtw_powertracking_type:default init value:64 (uint)
parm: rtw_GLNA_type:default init value:0 (uint)
parm: rtw_TxBBSwing_2G:default init value:0xFF (uint)
parm: rtw_TxBBSwing_5G:default init value:0xFF (uint)
parm: rtw_OffEfuseMask:default open Efuse Mask value:0 (uint)
parm: rtw_FileMaskEfuse:default drv Mask Efuse value:0 (uint)
parm: rtw_rxgain_offset_2g:default RF Gain 2G Offset value:0 (uint)
parm: rtw_rxgain_offset_5gl:default RF Gain 5GL Offset value:0 (uint)
parm: rtw_rxgain_offset_5gh:uint
parm: rtw_rxgain_offset_5gm:default RF Gain 5GM Offset value:0 (uint)
parm: rtw_pll_ref_clk_sel:force pll_ref_clk_sel, 0xF:use autoload value (uint)
parm: rtw_tx_pwr_by_rate:0:Disable, 1:Enable, 2: Depend on efuse (int)
parm: rtw_tx_pwr_lmt_enable:0:Disable, 1:Enable, 2: Depend on efuse (int)
parm: rtw_target_tx_pwr_2g_a:2.4G target tx power (unit:dBm) of RF path A for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_2g_b:2.4G target tx power (unit:dBm) of RF path B for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_2g_c:2.4G target tx power (unit:dBm) of RF path C for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_2g_d:2.4G target tx power (unit:dBm) of RF path D for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_5g_a:5G target tx power (unit:dBm) of RF path A for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_5g_b:5G target tx power (unit:dBm) of RF path B for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_5g_c:5G target tx power (unit:dBm) of RF path C for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_target_tx_pwr_5g_d:5G target tx power (unit:dBm) of RF path D for each rate section, should match the real calibrate power, -1: undefined (array of int)
parm: rtw_tsf_update_pause_factor:num of bcn intervals to stay TSF update pause status (int)
parm: rtw_tsf_update_restore_factor:num of bcn intervals to stay TSF update restore status (int)
parm: rtw_phy_file_path:The path of phy parameter (charp)
parm: rtw_load_phy_file:PHY File Bit Map (int)
parm: rtw_decrypt_phy_file:Enable Decrypt PHY File (int)
parm: rtw_en_napi:int
parm: rtw_en_gro:int
parm: rtw_iqk_fw_offload:int
parm: rtw_ch_switch_offload:int

hai riavviato dopo averli compilati ?

Sì, dopo: sudo ./dkms-install.sh

Non ho riavviato dopo aver eseguito il remove…

Per scaramanzia prova a ridare :

sudo dracut -f -v 
è poi 
sudo grub2-mkconfig -o /boot/efi/EFI/fedora/grub.cfg

è riavvia
:slightly_smiling_face:

Se non funziona ancora rimuovi i driver , riavvia , è reinstalla i driver :slightly_smiling_face: accidendi a virtualbox :slightly_smiling_face: scusa ma era doveroso dirlo mai vista una cosa così strana

D’accordo, t’informo che per ora non va ancora… provo nuovamente…

Veramente, non sai quanto mi pento di averlo messo :frowning:

@edmondo
Quando avvio dkms-install.sh:

Error! echo
Your kernel headers for kernel 5.8.18-100.fc31.x86_64 cannot be found at
/lib/modules/5.8.18-100.fc31.x86_64/build or /lib/modules/5.8.18-100.fc31.x86_64/source.
You can use the --kernelsourcedir option to tell DKMS where it’s located.
Error! echo
Your kernel headers for kernel 5.8.18-100.fc31.x86_64 cannot be found at
/lib/modules/5.8.18-100.fc31.x86_64/build or /lib/modules/5.8.18-100.fc31.x86_64/source.
You can use the --kernelsourcedir option to tell DKMS where it’s located.
Finished running dkms install steps.

no installato dai repo è una favola , difatti io sconsiglio sempre l’uso di pacchetti esterni , comunque hai provato a dare i comandi dracut è grub poi riavviare ? se non funziona prova come ti ho scritto a rimuovere il driver riavviare è reinstallare il driver , di sicuro rimuovento virtualbox si è portato dietro qualche pacchetto che serviva comunque dopo queste 2 prove cè la terza :slightly_smiling_face:

sudo dnf install kernel-headers kernel-devel

dnf install kernel-headers kernel-devel:

Ultima verifica della scadenza dei metadati: 0:26:02 fa il sab 14 nov 2020, 00:02:52.
Package kernel-headers-5.5.17-200.fc31.x86_64 is already installed.
Dipendenze risolte.
Nessuna operazione da compiere.
Fatto!

Subito dopo: sudo ./dkms-install.sh

About to run dkms install steps…
Error! DKMS tree already contains: rtl8821ce-v5.5.2_34066.20200325
You cannot add the same module/version combo more than once.
Error! echo
Your kernel headers for kernel 5.8.18-100.fc31.x86_64 cannot be found at
/lib/modules/5.8.18-100.fc31.x86_64/build or /lib/modules/5.8.18-100.fc31.x86_64/source.
You can use the --kernelsourcedir option to tell DKMS where it’s located.
Error! echo
Your kernel headers for kernel 5.8.18-100.fc31.x86_64 cannot be found at
/lib/modules/5.8.18-100.fc31.x86_64/build or /lib/modules/5.8.18-100.fc31.x86_64/source.
You can use the --kernelsourcedir option to tell DKMS where it’s located.
Finished running dkms install steps.

Rimuovi il driver , è riavvia poi reinstalla il driver , è riavvia , in pratica non cede il percorso , è un errore di compilazione di dkms

Spero che non è stato rimosso pure questo pacchetto ( elfutils-libelf-devel)

Ho rimosso i driver, ho dato prima di procedere alla reinstallazione, il comando
“locate rtl8821ce” ed ecco il risultato:

/home/carrycode/rtl8821ce
/usr/src/rtl8821ce-v5.5.2_34066.20190614
/var/lib/dkms/rtl8821ce

Io però la cartella rtl8821ce non ce l’ho più nella mia home e nemmeno le altre directory!

git clone https://github.com/tomaspinho/rtl8821ce
cd rtl8821ce
chmod +x dkms-install.sh
chmod +x dkms-remove.sh
sudo ./dkms-remove.sh
sudo ./dkms-install.sh
sudo dnf install -y make git kernel-headers kernel-devel elfutils-libelf-devel dkms
installa prima le dipendenze poi scarichi il pacchetto è rimuovi i vecchi driver poi li reinstalli . dopo averli rimossi riavvia prima di reinstalarli

Ok, però non capisco come mai locate mi segnala ancora la presenza di quei file che non ho

Poi indaghiamo prima accendiamo il wifi

Ok :slightly_smiling_face:

Allora, ho eseguito
sudo dnf install -y make git kernel-headers kernel-devel elfutils-libelf-devel

I driver li avevo rimossi in precedenza e poi riavviato, quindi penso la sequenza vada bene.
Provo a reinstallarli oppure riavvio dopo le dipendenze e provo a reinstallare?

dopo che hai rimosso il tutto è messo le dipendenze riavvia , è prova a reinstallare i driver :slightly_smiling_face:

ok :slight_smile: provo e ti dico

Speriamo in bene :slightly_smiling_face: