Installazione scanner hp scanjet 6200c

ferdif · 10 Maggio 2020, 11:52am

Buon giorno, ho uno scanner hp scanjet 6200c , con hplip non mi riconosce il dispositivo , con xsane riesce a scansionare ma solo la prima volta poi devo riavviare .
Mi spiego meglio , la prima volta che entro in xsane mi da la possibilità di scegliere dispositivo o webcan o scanner , scelto scanner fatta un anteprima di scansione in bianco e nero sembra funzionare se tento di fare un’altra scansione scambiando parametri si pianta. Entrando nuovamente in xsane si imposta su webcam non mi da possibilita di selezionare dispositivo e non risponde più.

Caterpillar · 10 Maggio 2020, 11:52am

Facendo girare xsane come root, il problema si ripresenta?

# xsane

ferdif · 10 Maggio 2020, 11:52am

si. appena acceso riesco a fare prima scansione e mi si presenta la scelta fra webcam e scanner , poi se esco e rientro mi si imposta su webcam anche da root

Caterpillar · 10 Maggio 2020, 11:52am

Quando si verifica il problema esegui

# sane-find-scanner

poi posta l’output

ferdif · 10 Maggio 2020, 11:52am

E’ un po aleatorio , nel senso che in una precedente entrata mi aveva riconoscito scanner ma si era piantato
sotto le righe dopo che si è acquisita webcam
[root@localhost ~]# xsane
^C[root@localhost ~]# sane-find-scanner

sane-find-scanner will now attempt to detect your scanner. If the

result is different from what you expected, first make sure your

scanner is powered up and properly connected to your computer.

No SCSI scanners found. If you expected something different, make sure that

you have loaded a kernel SCSI driver for your SCSI adapter.

could not fetch string descriptor: Input/output error
could not fetch string descriptor: Input/output error
found USB scanner (vendor=0x03f0, product=0x0201) at libusb:004:003

Your USB scanner was (probably) detected. It may or may not be supported by

SANE. Try scanimage -L and read the backend’s manpage.

Not checking for parallel port scanners.

Most Scanners connected to the parallel port or other proprietary ports

can’t be detected by this program.

Caterpillar · 10 Maggio 2020, 11:52am

Modifica il post e metti tutto l’output dentro le tag “code”

Dammi anche

# lspci

ferdif · 10 Maggio 2020, 11:52am

ripeto comandi con xsane acquisizione non riuscita (piantato programma e rilanciato) riconusciuta webcam
[root@localhost ~]# xsane
[root@localhost ~]# sane-find-scanner

sane-find-scanner will now attempt to detect your scanner. If the

result is different from what you expected, first make sure your

scanner is powered up and properly connected to your computer.

No SCSI scanners found. If you expected something different, make sure that

you have loaded a kernel SCSI driver for your SCSI adapter.

could not fetch string descriptor: Input/output error
could not fetch string descriptor: Input/output error
found USB scanner (vendor=0x03f0, product=0x0201) at libusb:004:002

Your USB scanner was (probably) detected. It may or may not be supported by

SANE. Try scanimage -L and read the backend’s manpage.

Not checking for parallel port scanners.

Most Scanners connected to the parallel port or other proprietary ports

can’t be detected by this program.

[root@localhost ~]# lspci
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] RS780 Host Bridge
00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (ext gfx port 0)
00:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1)
00:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (PCIE port 2)
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.1 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller (rev 3a)
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v]
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03)
03:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

Caterpillar · 10 Maggio 2020, 11:52am

Hai sbagliato a mettere le tag, devi metterle all’inizio e alla fine di ciò che incolli, in maniera che venga così

[quote=ferdif]ripeto comandi con xsane acquisizione non riuscita (piantato programma e rilanciato) riconusciuta webcam

[code][root@localhost ~]# xsane
[root@localhost ~]# sane-find-scanner

sane-find-scanner will now attempt to detect your scanner. If the

result is different from what you expected, first make sure your

scanner is powered up and properly connected to your computer.

No SCSI scanners found. If you expected something different, make sure that

you have loaded a kernel SCSI driver for your SCSI adapter.

could not fetch string descriptor: Input/output error
could not fetch string descriptor: Input/output error
found USB scanner (vendor=0x03f0, product=0x0201) at libusb:004:002

Your USB scanner was (probably) detected. It may or may not be supported by

SANE. Try scanimage -L and read the backend’s manpage.

Not checking for parallel port scanners.

Most Scanners connected to the parallel port or other proprietary ports

can’t be detected by this program.[/code]

[root@localhost ~]# lspci 00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.1 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller 00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller (rev 3a) 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller 00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge 00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) 03:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)[/quote]

Ora posta l’output di

# lsusb

ferdif · 10 Maggio 2020, 11:52am

[root@localhost ~]# lsusb

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 13d3:5130 IMC Networks
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 03f0:0201 Hewlett-Packard ScanJet 6200c
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:c05a Logitech, Inc. M90/M100 Optical Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Caterpillar · 10 Maggio 2020, 11:52am

Rileggi un attimo il mio post circa l’utilizzo della tag CODE, dopodichè modifica il tuo post.
Grazie

ferdif · 10 Maggio 2020, 11:52am

[code][root@localhost ~]# lsusb

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 13d3:5130 IMC Networks
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 03f0:0201 Hewlett-Packard ScanJet 6200c
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:c05a Logitech, Inc. M90/M100 Optical Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub[/code]

Caterpillar · 10 Maggio 2020, 11:52am

Output di

# rpm -qa sane*

# cat /etc/sane.d/net.conf

ferdif · 10 Maggio 2020, 11:52am

[root@localhost ~]# rpm -qa sane* sane-backends-drivers-scanners-1.0.24-7.fc20.x86_64 sane-backends-drivers-cameras-1.0.24-7.fc20.x86_64 sane-backends-doc-1.0.24-7.fc20.noarch sane-backends-devel-1.0.24-7.fc20.x86_64 sane-backends-libs-1.0.24-7.fc20.x86_64 sane-frontends-1.0.14-18.fc20.x86_64 sane-backends-1.0.24-7.fc20.x86_64

[code][root@localhost ~]# cat /etc/sane.d/net.conf

This is the net backend config file.

net backend options

Timeout for the initial connection to saned. This will prevent the backend

from blocking for several minutes trying to connect to an unresponsive

saned host (network outage, host down, …). Value in seconds.

connect_timeout = 60

saned hosts

Each line names a host to attach to.

If you list “localhost” then your backends can be accessed either

directly or through the net backend. Going through the net backend

may be necessary to access devices that need special privileges.

localhost

[/code]

Caterpillar · 10 Maggio 2020, 11:52am

Modifica

/etc/sane.d/net.conf

in tal maniera

[code]# This is the net backend config file.

net backend options

Timeout for the initial connection to saned. This will prevent the backend

from blocking for several minutes trying to connect to an unresponsive

saned host (network outage, host down, …). Value in seconds.

connect_timeout = 60

saned hosts

Each line names a host to attach to.

If you list “localhost” then your backends can be accessed either

directly or through the net backend. Going through the net backend

may be necessary to access devices that need special privileges.

localhost
hp
[/code]
Poi vedi se il problema persiste

Inoltre già che ci sei posta

# cat /etc/sane.d/dll.conf

ferdif · 10 Maggio 2020, 11:52am

ho provato ad editare come da post precedente. la situazione sembra peggiorata , non solo il problema si ripresenta ma non sono riuscito neanche a fare una scansione , il processo sembra molto più lento.
la riga che mi hai richiesta è questa sotto ma considera che avevo provato ad aggiungere hp6200 come sotto mostrato aggiungendo anche in
/etc/sane.d/hp6200.conf con le seguenti righe (copiato e modificato da hp5400.conf gia esistente)

hp6200.conf

See man sane-hp5400 for a description.

HP 6200C

usb 0x03F0 0x0201

Device filename to use for scanner access

Uncomment the following line if autodetection fails

#/dev/usbscanner

[code][root@localhost ~]# cat /etc/sane.d/dll.conf

enable the next line if you want to allow access through the network:

net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
canon_dr
#canon_pp
cardscan
coolscan
#coolscan2
coolscan3
#dc25
#dc210
#dc240
dell1600n_net
dmc
epjitsu
#epson
epson2
fujitsu
#gphoto2
genesys
gt68xx
hp
hp3900
hpsj5s
hp3500
hp4200
hp5400
hp5590
hp6200
hpljm1005
hs2p
ibm
kodak
kodakaio
kvs1025
kvs20xx
leo
lexmark
ma1509
magicolor
matsushita
microtek
microtek2
mustek
#mustek_pp
mustek_usb
mustek_usb2
nec
niash
#p5
pie
pint
pixma
plustek
#plustek_pp
#pnm
qcam
ricoh
rts8891
s9036
sceptre
sharp
sm3600
sm3840
snapscan
sp15c
#st400
#stv680
tamarack
teco1
teco2
teco3
#test
u12
umax
#umax_pp
umax1220u
v4l
xerox_mfp
hpaio[/code]

Caterpillar · 10 Maggio 2020, 11:52am

[list=*]
]Hai riletto il tuo post? È formattato male, qui tendiamo a non leggere i post formattati male, è una questione di buona educazione verso chi sta spendendo il proprio tempo per aiutare il prossimo/]
]Per favore non aggiungere cose mentre ti sto facendo eseguire vari passi per vedere come mettere apposto il tuo problema. Ripristina tutto ciò che hai fatto e che non era stato chiesto/]
[/list]
Una volta ripristinato il tutto ridammi

# cat /etc/sane.d/dll.conf

# ls /etc/sane.d/

# cat /etc/sane.d/net.conf

ferdif · 10 Maggio 2020, 11:52am

ho avuto problemi con l’altro pc.
Attualmente sono su un altro pc dove non avevo modificato nessun codice, cosa che avevo fatto prima di avere fatto la chiamata di aiuto., il file dll.conf mi ha ricordato che avevo fatto delle modifiche nel tentativo di migliorare la situazione.

[code][root@localhost ~]# cat /etc/sane.d/dll.conf

enable the next line if you want to allow access through the network:

net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
canon_dr
#canon_pp
cardscan
coolscan
#coolscan2
coolscan3
#dc25
#dc210
#dc240
dell1600n_net
dmc
epjitsu
#epson
epson2
fujitsu
#gphoto2
genesys
gt68xx
hp
hp3900
hpsj5s
hp3500
hp4200
hp5400
hp5590
hpljm1005
hs2p
ibm
kodak
kodakaio
kvs1025
kvs20xx
leo
lexmark
ma1509
magicolor
matsushita
microtek
microtek2
mustek
#mustek_pp
mustek_usb
mustek_usb2
nec
niash
#p5
pie
pint
pixma
plustek
#plustek_pp
#pnm
qcam
ricoh
rts8891
s9036
sceptre
sharp
sm3600
sm3840
snapscan
sp15c
#st400
#stv680
tamarack
teco1
teco2
teco3
#test
u12
umax
#umax_pp
umax1220u
v4l
xerox_mfp
hpaio[/code]

[root@localhost ~]# ls /etc/sane.d/ abaton.conf dll.d ma1509.conf saned.conf agfafocus.conf dmc.conf magicolor.conf sceptre.conf apple.conf epjitsu.conf matsushita.conf sharp.conf artec.conf epson2.conf microtek2.conf sm3840.conf artec_eplus48u.conf epson.conf microtek.conf snapscan.conf avision.conf fujitsu.conf mustek.conf sp15c.conf bh.conf genesys.conf mustek_pp.conf st400.conf canon630u.conf gphoto2.conf mustek_usb.conf stv680.conf canon.conf gt68xx.conf nec.conf tamarack.conf canon_dr.conf hp3900.conf net.conf teco1.conf canon_pp.conf hp4200.conf net.conf~ teco2.conf cardscan.conf hp5400.conf p5.conf teco3.conf coolscan2.conf hp.conf pie.conf test.conf coolscan3.conf hpsj5s.conf pixma.conf u12.conf coolscan.conf hs2p.conf plustek.conf umax1220u.conf dc210.conf ibm.conf plustek_pp.conf umax.conf dc240.conf kodakaio.conf qcam.conf umax_pp.conf dc25.conf kodak.conf ricoh.conf v4l.conf dell1600n_net.conf leo.conf rts8891.conf xerox_mfp.conf dll.conf lexmark.conf s9036.conf

[code][root@localhost ~]# cat /etc/sane.d/net.conf

This is the net backend config file.

net backend options

Timeout for the initial connection to saned. This will prevent the backend

from blocking for several minutes trying to connect to an unresponsive

saned host (network outage, host down, …). Value in seconds.

connect_timeout = 60

saned hosts

Each line names a host to attach to.

If you list “localhost” then your backends can be accessed either

directly or through the net backend. Going through the net backend

may be necessary to access devices that need special privileges.

localhost
hp[/code]

purtroppo il risultato non cambia continua a non funzionare e si ripresenta la seconda volta che si entra in xsane la webcam senza possibilità di scelta

Caterpillar · 10 Maggio 2020, 11:52am

Modifica

/etc/sane.d/net.conf

in tal maniera

[code]# This is the net backend config file.

net backend options

Timeout for the initial connection to saned. This will prevent the backend

from blocking for several minutes trying to connect to an unresponsive

saned host (network outage, host down, …). Value in seconds.

connect_timeout = 60

saned hosts

Each line names a host to attach to.

If you list “localhost” then your backends can be accessed either

directly or through the net backend. Going through the net backend

may be necessary to access devices that need special privileges.

#localhost
hp
[/code]

Noti miglioramenti?

ferdif · 10 Maggio 2020, 11:52am

no dopo aver fatto il primo accesso in xsane mi da la possibilità di scegliere dispositivo , al successivo accesso mi da ancora la webcam enon riesce a scannerizzarec

Caterpillar · 10 Maggio 2020, 11:52am

Ripristiniamo tutto come in origine

/etc/sane.d/net.conf

in tal maniera

[code]# This is the net backend config file.

net backend options

Timeout for the initial connection to saned. This will prevent the backend

from blocking for several minutes trying to connect to an unresponsive

saned host (network outage, host down, …). Value in seconds.

connect_timeout = 60

saned hosts

Each line names a host to attach to.

If you list “localhost” then your backends can be accessed either

directly or through the net backend. Going through the net backend

may be necessary to access devices that need special privileges.

#localhost
[/code]

Dopodiché apri una segnalazione bugreport per tale problema all’indirizzo http://www.sane-project.org/bugs.html
A questo punto sono quasi sicuro che sia un bug, perché se fosse stato un problema di configurazione allora non avrebbe funzionato affatto. A conferma di ciò il fatto che provando a modificare le configurazioni si peggiorava la situazione.