Ciao ragazzi!! ho da poco acquistato una stampante multifunzione canon mx 410 e non riesco a farla funzionare sotto fedora 14. Mi potreste aiutare? Cerco di farla funzionare via wifi…
Grazie a tutti
http://www.canon.it/Support/Consumer_Products/products/Fax__Multifunctionals/InkJet/PIXMA_MX_series/PIXMA_MX410.aspx?type=download&page=1 trovi i driver Linux per la stampante.
Hai problemi a installare ?
Grazie per la risposta… Sono riuscito ad installarla via cavo… Ma cercavo di farla funzionare via wireless ma non ci riesco…
fra l’altro i driver che mi hai linkato non vanno xD
Cosa significa ‘non vanno’ ?
ho scaricato i driver per lo scanner Linux IJ Scanner Driver. Settato il firewall come scritto nel manuale, quando vado a far partire l’install.sh mi dice:
An error occurred. The package management system cannot be identified.
./install.sh: line 337: : =: unary operator expected
ScanGear MP Ver.1.70-1 for Linux
Copyright CANON INC. 2007-2011
All Rights Reserved.
==================================================
An error occurred. The package management system cannot be identified.
La guida dice anche che:
With openSUSE 11.3, the system environment may trigger a missing dependency error, and driver installation may fail. If that hapens, install the libpng12-0 package, and execute “(2) Installing ScanGear” again.
Però questo pack non lo trovo su internet… quanto meno per il mio pc (32 bit)
Nello stesso archivio ci sono gli rpm da installare; usa quelli direttamente.
Ho installato gli rpm. Ho provato a fare una sansione (col cavo collegato) ma il pc non acquisisce nulla.
$ rpm -qa | grep -e scangear -e cnijrpm -qa | grep -e scangear -e cnij
scangearmp-mx410series-1.70-1.i386
scangearmp-common-1.70-1.i386
Mancano quelli della stampante.
rpm -qa | grep -e scangear -e cnij
cnijfilter-mx410series-3.50-1.i386
scangearmp-mx410series-1.70-1.i386
cnijfilter-common-3.50-1.i386
scangearmp-common-1.70-1.i386
Cos’altro devo fare? Lo scanner ancora non funziona…
Prova ad aprire gimp e a aquisire l’immagine dallo scanner.
Naturalmente imposta la stampante-scanner come predefinita.
Niente da fare… Sembra come se non comunica con il pc… però quando invio una stampa dal pc funziona…
Colleghi la stampate via cavo usb?
Output di:
$ sane-find-scanner
$ scanimage -LSi, la stampante multifunzione la collego via cavo…
Ho provato i comandi che mi hai chiesto ed ecco il risultato:
[Yoshi@Luca ~]$ sane-find-scanner
sane-find-scanner will now attempt to detect your scanner. If the
result is different from what you expected, first make sure your
scanner is powered up and properly connected to your computer.
No SCSI scanners found. If you expected something different, make sure that
you have loaded a kernel SCSI driver for your SCSI adapter.
found USB scanner (vendor=0x04a9 [Canon], product=0x174e [MX410 series]) at libusb:001:003
Your USB scanner was (probably) detected. It may or may not be supported by
SANE. Try scanimage -L and read the backend’s manpage.
Not checking for parallel port scanners.
Most Scanners connected to the parallel port or other proprietary ports
can’t be detected by this program.
You may want to run this program as root to find all devices. Once you
found the scanner devices, be sure to adjust access permissions as
necessary.
[Yoshi@Luca ~]$ scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
Output di lsusb:
$ lsusbCon scanner collegato e acceso.
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:c05d Logitech, Inc.
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 04a9:174e Canon, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Sei certo che i driver per lo scanner siano correttamente installati?
Togli il cavo usb, attendi, ricollega, attendi pochi secondi e poi fornisci questo output:
$ dmesg|tail -n 20Per quanto riguarda i driver, per sicurezza ho provato a far partire gli rpm scaricati dal sito della canon e, come risultato, mi dice che sono già installati…
Cmq:
[root@Luca Yoshi]# dmesg|tail -n 20
501.333345] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
501.333766] cfg80211: Calling CRDA for country: IT
501.593289] cfg80211: Regulatory domain changed to country: IT
501.593295] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
501.593300] (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
501.593305] (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
501.593309] (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
501.593313] (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
512.194025] wlan0: no IPv6 routers present
848.299135] usb 1-3: USB disconnect, address 3
848.300326] usblp0: removed
848.300450] usblp1: removed
895.994050] usb 1-3: new high speed USB device using ehci_hcd and address 4
896.112328] usb 1-3: New USB device found, idVendor=04a9, idProduct=174e
896.112333] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
896.112337] usb 1-3: Product: MX410 series
896.112340] usb 1-3: Manufacturer: Canon
896.112343] usb 1-3: SerialNumber: 31DDEC
896.133113] usblp0: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x04A9 pid 0x174E
896.136488] usblp1: USB Bidirectional printer dev 4 if 2 alt 0 proto 2 vid 0x04A9 pid 0x174E
Output:
$ rpm -qa|grep sane